Home / Appliances / Garbage Disposal Installation
Garbage Disposal Installation
Most appliance failures traced to electrical are loose terminations. Appliance circuits fail at the connection, not in the middle of the run, which is why a loose terminal shows up as a dead appliance.
Garbage Disposal Installation in O’Fallon and across St. Charles, St. Louis, Lincoln and Warren counties.
Owner-operated by Clint Ehman. Seventeen years in the trade, four of them running his own shop.
5.0 from 94 Google reviews · BBB A+ since 2022
What this work actually involves
The circuit is matched to the appliance’s own data plate rather than to what was there before.
The order is always the same: reproduce it, measure it, say what the number means, fix the thing the number points at. Nothing gets bundled on the way past.
Permits and inspections happen where the municipality requires them, and the panel is left labeled. One person does all of it.
When people call about this
- A breaker that trips on a cycle
- An appliance with a scorched plug
- A pool pump on a shared circuit
- Mini-split installed with no circuit
Why people choose Clint for it
What the reviews keep mentioning is being told what the problem actually was. That is what an owner-operated shop can do and a dispatch model structurally cannot.
Seventeen years in the trade, 5.0 from 94 Google reviews, and BBB accredited A+ since December 2022.
Where this is done
O’Fallon and the surrounding St. Charles County suburbs, out through St. Louis County and St. Louis City, and into Lincoln and Warren counties. Roughly a fifty mile radius.
See the full service area, or the rest of our appliances & hvac work.
Read the data plate, not the old circuit
Every appliance states what it expects: volts, amps or watts, and often the circuit size. That plate is the specification, and a replacement appliance frequently asks for more than the one it replaced.
Same-size replacements still change things. Induction cooktops and heat-pump dryers draw differently from what was there in 1996.
Dedicated circuits and why appliances want them
A large appliance on a shared circuit is a nuisance trip waiting to happen, and worse, it makes diagnosis hard because the blame gets spread across whatever else is on the line.
One circuit, one appliance, sized to the plate and labeled at the panel with what it feeds. That is what makes a future fault a ten minute diagnosis rather than an afternoon.
Disposals, switches and the cabinet under the sink
A disposal wants its own switch where you can reach it without looking under the sink, and a receptacle or connection inside a cabinet that is wet more often than any other in the house.
Protection is matched to the location, the connection is made so it survives the cabinet, and the switch goes where a hand actually goes.
What makes this harder in older housing stock
Across this metro the recurring complications are predictable: no equipment ground, aluminum branch wiring from the mid-seventies, knob-and-tube buried in blown-in insulation, panels that have been added to several times, and splices in places the code has not allowed for decades.
Those turn a simple job into a decision about scope. The decision gets put to you with the reading behind it rather than made quietly and billed.
Why the diagnosis comes before the quote
A symptom has several possible causes with very different prices, and the only thing that separates them is a measurement. Quoting the expensive one covers the risk; quoting the cheap one and finding the expensive one mid-job is worse.
So the reading happens first, you are told what it says, and then the work is scoped to it. Where the honest answer is the small repair, that is the answer you get, even when the larger job pays better.
“Infinity came out for same day service after an electric line had been cut in my yard. He was able to locate and correct it very quickly, eliminating any risk of injury or additional power outage.”
Melissa Johnson · Google review
How the visit goes
- The call
Which appliance, and whether it is new, replacing something, or failing.
- The measurement
The appliance’s data plate against the existing circuit, and the condition of the terminations at both ends.
- The finding
Whether the circuit is right, needs upgrading, or is fine and the problem is a connection.
- The work
Circuit matched to the plate, disconnect and bonding where water is involved, terminations torqued to specification, tested under load.
What the job includes
- Circuit matched to the appliance’s own data plate
- Disconnects and bonding where water is involved
- Terminations torqued to specification
- Correct receptacle or hardwired connection as the appliance requires
- Permit and inspection where required
- Testing under load before we leave
What it does not
- Supplying or repairing the appliance
- Plumbing and gas connections
- Appliance haul-away
Anything that is not an electrical problem gets identified as such and handed on. See the work itself, or send the details.
Related appliances & hvac work
Garbage Disposal Installation across the metro
Housing stock varies sharply across the counties here, and so does the work. Out of O’Fallon across thirty municipalities, where the permit process changes more than the work does.
St. Louis County
Dozens of municipalities, each with its own occupancy inspection and its own thresholds. Knowing which authority has the address matters as much as knowing the house.
St. Louis City
Much of this stock is two and four family, which means shared services and panels that are rarely labeled accurately.
Lincoln County
Rural properties where the panel is fine and the two hundred foot run to the barn is the actual job.
See which towns fall inside the radius on the service areas page.
Questions worth asking first.
Why did my dryer outlet burn?
Terminations at a dryer receptacle see heat and vibration for decades. Discolouration there is a connection problem, and the receptacle gets replaced rather than reused.
My new appliance will not run. Is it the appliance?
Often it is the circuit. The data plate states what the appliance expects, and comparing that to the existing circuit usually explains it in one visit.
Does a hot tub need its own disconnect?
Yes, with bonding, and placement is specified by code. It is one of the items inspectors check first on spa work.
What do your reviews say?
5.0 from 94 Google reviews, and A+ accreditation with the BBB held since 2022. The reviews are on the reviews page with links to where each was posted.
Who actually shows up?
Clint Ehman. Infinity Electric is owner-operated, so the person who answers the phone is the person who measures your panel and pulls the permit. There is no dispatcher and no commissioned salesman.
Get the measurement first.
The reading comes before the number, so you know what you are deciding about. Garbage Disposal Installation in O’Fallon and across the metro.
Mon-Thu 8-5 · Fri 8-4 · Sat 10-3. If a message suits you better, there is a form.