Home / Appliances / Hot Tub Electrical Installation
Hot Tub Electrical Installation
Replacing like for like still changes the load more often than people expect. Hot tubs, pools and saunas carry their own rules, and the inspector will know them even if the installer did not.
Hot Tub Electrical Installation in O’Fallon and across St. Charles, St. Louis, Lincoln and Warren counties.
Clint Ehman does the work himself. Seventeen years in the trade, Infinity Electric since June 2022.
5.0 from 94 Google reviews · BBB A+ since 2022
What this work actually involves
Disconnects and bonding are installed where water is involved, because that is what the code is protecting against.
Clint measures before he quotes. The reading comes first, then what it means, then the one repair that solves it. If the honest answer is smaller than what you called about, that is the answer you get, even when the bigger job pays better.
Work that needs a permit gets one, and work that needs an inspection is left ready for it. One person does the diagnosis and the repair, so nothing is lost between a salesman and a technician.
When people call about this
- An appliance with a scorched plug
- A pool pump on a shared circuit
- Mini-split installed with no circuit
- A new range or dryer that will not run
Why people choose Clint for it
The diagnosis and the repair are the same person’s work, which is why the explanation you get is first-hand rather than relayed.
Five point zero from 94 Google reviews, A+ with the BBB since December 2022, and seventeen years in the trade behind it.
Where this is done
Thirty towns across five jurisdictions, worked out of O’Fallon. The housing stock and the inspection process both change as you move across them.
See the full service area, or the rest of our appliances & hvac work.
Wet locations and the rules that follow
Dishwashers, disposals and anything in a laundry sit where leaks happen, which brings protection requirements, specific connection methods and in some cases bonding. The rules are not arbitrary and inspectors know them well.
So those installs get the right protection for the location and a listed connection rather than a taped splice in a damp cabinet.
The data plate settles it
Every appliance carries a plate stating what it draws and what circuit it needs. That plate, not the old circuit and not the showroom brochure, governs the install, and it is the first thing to look at when a new appliance will not run right.
A replacement frequently draws differently from what it replaced. Induction asks more than a coil range, a heat pump water heater asks differently from a resistance one, and a modern dryer is not the dryer the circuit was run for.
What the tub’s own listing requires
A tub needs a dedicated GFCI-protected circuit, a disconnect in sight of the tub but at the required distance from the water, and bonding of the metal parts around it. The manufacturer’s listing sets the numbers and the inspector checks against them.
The work therefore starts with the data plate rather than a guess. Bonding is the part most often missing on existing installs and the part that matters most.
Why the diagnosis comes before the quote
A symptom has several possible causes with very different prices, and the only thing that separates them is a measurement. Quoting the expensive one covers the risk; quoting the cheap one and finding the expensive one mid-job is worse.
So the reading happens first, you are told what it says, and then the work is scoped to it. Where the honest answer is the small repair, that is the answer you get, even when the larger job pays better.
What makes this harder in older housing stock
Across this metro the recurring complications are predictable: no equipment ground, aluminum branch wiring from the mid-seventies, knob-and-tube buried in blown-in insulation, panels that have been added to several times, and splices in places the code has not allowed for decades.
Those turn a simple job into a decision about scope. The decision gets put to you with the reading behind it rather than made quietly and billed.
“Clint came out installed me a large 200 amp panel put some new dedicated lines in my basement and garage he did great clean work all inspections passed he was thorough and knowledgeable. I will have him back out again.”
Jason Holtzman · Google review
How the visit goes
- The call
Which appliance, and whether it is new, replacing something, or failing.
- The measurement
The appliance’s data plate against the existing circuit, and the condition of the terminations at both ends.
- The finding
Whether the circuit is right, needs upgrading, or is fine and the problem is a connection.
- The work
Circuit matched to the plate, disconnect and bonding where water is involved, terminations torqued to specification, tested under load.
What the job includes
- Circuit matched to the appliance’s own data plate
- Disconnects and bonding where water is involved
- Terminations torqued to specification
- Correct receptacle or hardwired connection as the appliance requires
- Permit and inspection where required
- Testing under load before we leave
Related appliances & hvac work
Hot Tub Electrical Installation across the metro
Where the house is changes what the work involves. Clint works out of O’Fallon across five jurisdictions, and the same service means different work in each.
Lincoln County
Outbuildings count as separate structures in code terms: a disconnect at the building, a grounding electrode there, and a feeder sized for the distance.
Warren County
Warren County mixes newer builds with older farm properties, and generator work comes up more often there than it does in town.
St. Charles County
The subdivisions here were wired correctly for what houses drew at the time. A charger, a heat pump and a finished lower level later, the arithmetic no longer works out.
Every municipality covered is listed on the service areas page.
Questions worth asking first.
My new appliance will not run. Is it the appliance?
Often it is the circuit. The data plate states what the appliance expects, and comparing that to the existing circuit usually explains it in one visit.
Does a hot tub need its own disconnect?
Yes, with bonding, and placement is specified by code. It is one of the items inspectors check first on spa work.
Will my induction range fit the existing circuit?
Often not. Induction generally draws more than the coil range it replaces, and the appliance data plate settles it before delivery day.
Who actually shows up?
Clint Ehman. Infinity Electric is owner-operated, so the person who answers the phone is the person who measures your panel and pulls the permit. There is no dispatcher and no commissioned salesman.
Are you licensed and insured?
Licensed, bonded and insured, with workers compensation coverage, and accredited A+ with the BBB since 2022.
Worth a call before it gets worse.
Heat, a smell or a repeated trip is the house reporting something real. Hot Tub Electrical Installation in O’Fallon and across the metro.
Mon-Thu 8-5 · Fri 8-4 · Sat 10-3. Emergencies outside that are still worth the call, or message instead.