Home / Safety / Electrical Safety Corrections
Electrical Safety Corrections
Intermittent problems are the hardest and the most important to reproduce. Most electrical faults announce themselves before they fail, in heat, smell or a breaker that keeps tripping.
Electrical Safety Corrections in O’Fallon and across St. Charles, St. Louis, Lincoln and Warren counties.
Owner-operated: the person who answers the phone is the person who measures it.
5.0 from 94 Google reviews · BBB A+ since 2022
What this work actually involves
You get told what the reading was and what it means, including when the honest answer is a small repair.
First the reading, then the explanation, then the repair scoped to what was actually found. If that turns out smaller than the job you called about, that is what you are charged for.
Work needing a permit gets one and work needing an inspection is left ready for it. There is no handoff between whoever quotes and whoever fixes, because they are the same person.
When people call about this
- An inspection report before a closing
- Half the house without power
- Warm cover plates
- A burning smell near a panel or outlet
Why people choose Clint for it
The diagnosis and the repair are the same person’s work, which is why the explanation you get is first-hand rather than relayed.
Five point zero from 94 Google reviews, A+ with the BBB since December 2022, and seventeen years in the trade behind it.
Where this is done
A roughly fifty mile working radius from O’Fallon, covering thirty municipalities across five jurisdictions in the St. Louis metro.
See the full service area, or the rest of our safety & code work.
What an inspector is actually reading
Grounding and bonding, protection in wet locations, the panel with its cover off, terminations at large loads, and the specific hazards this housing stock produces. That short list is most of any inspection report in this metro.
Working from their written items keeps a correction honest and the re-inspection short. Opinions about what else might be wrong are a separate conversation and get flagged as such.
How a fault is actually found
Diagnosis is a process of division. Measure at the panel, measure at the point of failure, then split the circuit until the fault is on one side of the split.
That is slower to describe than swapping parts and much faster in practice, because it ends with an answer instead of a list of things that were not the problem.
Correcting a hazard, not a list of upsells
The hazards that genuinely need correcting are specific: open splices, doubled lugs, missing grounds where a ground is required, protection missing in wet locations, and heat damage at terminations.
Those get corrected. Items that are old and working are identified as such rather than sold as emergencies.
Why a diagnosis is worth paying for
A measurement that comes back saying the service is fine and one circuit is overloaded saves the cost of a service upgrade. That is the most common outcome of a load calculation, and it only has value because it is honest in both directions.
An inspection that never finds anything is not a good inspection and neither is one that always finds plenty. What makes it useful is that the finding is a reading you can check.
What gets left behind when the work is done
A labeled panel, accessible junctions, the old parts if you want to see them, and a straight account of anything found along the way that was not part of the call.
Where something else was found, you get told what it is and whether it needs doing now, later or not at all. That third answer is a real answer and it gets used.
“Clint came out installed me a large 200 amp panel put some new dedicated lines in my basement and garage he did great clean work all inspections passed he was thorough and knowledgeable. I will have him back out again.”
Jason Holtzman · Google review
How the visit goes
- The call
What you are seeing, smelling or hearing, and when it started. Heat and smell move you up the day.
- The measurement
Reproduce the symptom, then divide the circuit until the fault is on one side of the split. Measurement at the panel and at the point of failure.
- The finding
What it was, with the reading. Including when the answer is one loose connection rather than the rewire you were braced for.
- The work
Correction scoped to the finding, permitted and re-inspected where the municipality requires it, and documentation you can hand to an inspector or a buyer.
What the job includes
- Reproducing the symptom before anything is replaced
- Measurement at the panel and at the fault
- A plain-words finding with the number that supports it
- Correction scoped to the finding, nothing bundled
- Permit and re-inspection where a municipality requires it
- Documentation you can hand to an inspector or a buyer
What it does not
- Replacing parts that test sound
- Opinions where a measurement is possible
- Work outside electrical, though we will say who to call
Plumbing, HVAC and structural work get a pointer to someone who does them properly. There is a gallery of finished jobs, and a form if that is easier than calling.
Related safety & code work
Electrical Safety Corrections across the metro
Where the house is changes what the work involves. The housing stock changes as you cross this metro, and so does what the job involves.
St. Louis County
Dozens of municipalities, each with its own occupancy inspection and its own thresholds. Knowing which authority has the address matters as much as knowing the house.
St. Louis City
St. Louis City is century brick with shared walls and basement panels that have been added to five times. Code corrections and occupancy inspections are the common call.
Lincoln County
Outbuildings count as separate structures in code terms: a disconnect at the building, a grounding electrode there, and a feeder sized for the distance.
Thirty towns across five jurisdictions, all on the service areas page.
Questions worth asking first.
There is a burning smell near my panel. What should I do?
Treat that as urgent. Turn off what you safely can and call. Heat and smell at a panel or outlet are the two symptoms that should never wait for a scheduled visit.
Can you handle the items on my inspection report?
Yes. Send the report. The items get corrected, permitted where the municipality requires it, and re-inspected so the file closes before your closing date.
My lights flicker across the whole house. Is that urgent?
Potentially. A whole-house flicker, especially when a large motor starts, can mean a failing service neutral, which can damage equipment. That gets measured at the panel before anything inside is touched.
How long have you been doing this?
Clint has seventeen years in the trade and has been running his own shop out of O’Fallon since 2022.
What do your reviews say?
5.0 from 94 Google reviews, and A+ accreditation with the BBB held since 2022. The reviews are on the reviews page with links to where each was posted.
Tell him what the house is doing.
You will get a reading and a straight answer about what it means, including the answer where the fix is small. Electrical Safety Corrections in O’Fallon and across the metro.
Mon-Thu 8-5 · Fri 8-4 · Sat 10-3 · or ask online