Home / Appliances / Electric Dryer Wiring
Electric Dryer Wiring
Replacing like for like still changes the load more often than people expect. Appliance circuits fail at the connection, not in the middle of the run, which is why a loose terminal shows up as a dead appliance.
Electric Dryer Wiring in O’Fallon and across St. Charles, St. Louis, Lincoln and Warren counties.
Owner-operated by Clint Ehman. Seventeen years in the trade, four of them running his own shop.
5.0 from 94 Google reviews · BBB A+ since 2022
What this work actually involves
Disconnects and bonding are installed where water is involved, because that is what the code is protecting against.
A number follows a measurement here, never a guess. You get told what the reading was and what it means before any work is agreed, including on the days when the answer is one loose connection.
Permitted and inspected where the address requires it, labeled at the panel, and done by the person who diagnosed it rather than handed down a chain.
When people call about this
- An appliance with a scorched plug
- A pool pump on a shared circuit
- Mini-split installed with no circuit
- A new range or dryer that will not run
Why people choose Clint for it
Nobody here earns more by finding more. That is the structural reason the small answer gets given when the small answer is true.
Seventeen years in the trade, Infinity Electric founded in June 2022, 5.0 from 94 Google reviews, BBB accredited A+.
Where this is done
O’Fallon and the surrounding St. Charles County suburbs, out through St. Louis County and St. Louis City, and into Lincoln and Warren counties. Roughly a fifty mile radius.
See the full service area, or the rest of our appliances & hvac work.
Read the data plate, not the old circuit
Every appliance states what it expects: volts, amps or watts, and often the circuit size. That plate is the specification, and a replacement appliance frequently asks for more than the one it replaced.
Same-size replacements still change things. Induction cooktops and heat-pump dryers draw differently from what was there in 1996.
Why terminations fail before conductors do
The wire inside a wall almost never fails. The connections at either end do, because that is where heat cycles, vibration and torque all land. A discoloured dryer receptacle or a warm range connection is a termination problem, and it does not resolve itself.
The fix is to redo the terminations properly and replace devices that show heat rather than reuse them. Torque to specification is not a formality here; it is the difference between a connection that lasts and one that cooks.
Why dryer circuits get looked at
A dryer is a large dedicated load and its receptacle sees heat and vibration for decades. Burned or discoloured terminals at the outlet are common and are a connection problem, not an appliance problem.
The circuit gets checked against the appliance plate, the terminations are redone properly, and the receptacle gets replaced rather than reused if it shows heat.
Why a new appliance exposes an old circuit
An appliance arriving is often the first time in decades anything asked that circuit for its rated load, and that is when a tired termination finally shows itself. The appliance gets blamed and the connection is the cause.
Checking the circuit against the new plate before delivery turns that into a planned half hour instead of a failed install day.
Permits, inspections and why they vary here
Requirements genuinely differ across this metro. O’Fallon, St. Charles, St. Peters, the St. Louis County municipalities and St. Louis City each run their own process, and what one treats as a minor repair another permits and inspects.
Work that needs a permit gets one, and work that needs an inspection is left ready for it with the panel labeled and the junctions accessible. That matters most before a closing, when an inspector’s written item becomes someone’s negotiating position.
“Clint came out installed me a large 200 amp panel put some new dedicated lines in my basement and garage he did great clean work all inspections passed he was thorough and knowledgeable. I will have him back out again.”
Jason Holtzman · Google review
How the visit goes
- The call
Which appliance, and whether it is new, replacing something, or failing.
- The measurement
The appliance’s data plate against the existing circuit, and the condition of the terminations at both ends.
- The finding
Whether the circuit is right, needs upgrading, or is fine and the problem is a connection.
- The work
Circuit matched to the plate, disconnect and bonding where water is involved, terminations torqued to specification, tested under load.
What the job includes
- Circuit matched to the appliance’s own data plate
- Disconnects and bonding where water is involved
- Terminations torqued to specification
- Correct receptacle or hardwired connection as the appliance requires
- Permit and inspection where required
- Testing under load before we leave
What it does not
- Supplying or repairing the appliance
- Plumbing and gas connections
- Appliance haul-away
Anything outside electrical, you will be told who to call rather than sold it. See the work itself, or send the details.
Related appliances & hvac work
Electric Dryer Wiring across the metro
Housing stock varies sharply across the counties here, and so does the work. Out of O’Fallon across thirty municipalities, where the permit process changes more than the work does.
St. Charles County
Out here the panels are not old, they are full. Houses built through the 1990s and 2000s got services sized for the loads of their decade, and the loads have since changed.
St. Louis County
The obsolete panel brands concentrate in this county, because they were installed through exactly the decades this housing was built and upgraded.
St. Louis City
Fishing a wall is harder here and sometimes not possible, so the honest answer about opening one comes before the work rather than during it.
The full footprint, county by county, is on the service areas page.
Questions worth asking first.
Why did my dryer outlet burn?
Terminations at a dryer receptacle see heat and vibration for decades. Discolouration there is a connection problem, and the receptacle gets replaced rather than reused.
My new appliance will not run. Is it the appliance?
Often it is the circuit. The data plate states what the appliance expects, and comparing that to the existing circuit usually explains it in one visit.
Does a hot tub need its own disconnect?
Yes, with bonding, and placement is specified by code. It is one of the items inspectors check first on spa work.
How long have you been doing this?
Clint has seventeen years in the trade and has been running his own shop out of O’Fallon since 2022.
What do your reviews say?
5.0 from 94 Google reviews, and A+ accreditation with the BBB held since 2022. The reviews are on the reviews page with links to where each was posted.
Tell him what the house is doing.
You will get a reading and a straight answer about what it means, including the answer where the fix is small. Electric Dryer Wiring in O’Fallon and across the metro.
Mon-Thu 8-5 · Fri 8-4 · Sat 10-3. A written note works too.